生物质基固体材料中生物基含量测定方法的研究进展

doi:10.3969/j.issn.1673-5854.2016.05.010

Abstract

Abstract: The determination methods of bio-based content in bio-based solid material,including the selective dissolution method(SDM) and ¹⁴C method,were reviewed.The precision of SDM was relatively lower,and its sample preparation was more complex and time consuming.¹⁴C method contained liquid scintillation counting(LSC) method,which included CO₂ absorption method,direct LSC method and benzene synthesis,and accelerator mass spectrometry(AMS) method.CO₂ absorption method was simple,fast and low cost,but it was also low precision.This method was suitable for the sample requirement for not high precision.The sample preparation of direct LSC method was the simplest in all methods,but it had a high requirement on the samples.This method had a lot of interference factors which were difficult to be eliminated.Benzene synthesis method had high precision,but the sample pretreatment took time,and the measuring period was long.Accelerator mass spectrometry was a rapid detection method and also had high precision,but the equipment was extremely expensive.These all limited its application.Finally,the prospects for their future development were also presented.

Key words: solid material, bio-based content, selective dissolution, ¹⁴C method

CLC Number:

TQ35

DENG Kun-ming, WANG Peng-fei, MA Yan, WANG Hong-xiao, SHEN Juan-zhang, TAN Wei-hong. Research Progress of Determination Method of Bio-based Content in Bio-based Solid Material[J]. bce, 2016, 50(5): 53-59.

References

[1] 李婷. 固体生物质燃料中碳氢含量测定方法的研究[J]. 煤质技术,2009(5):14-17.
[2] NOR N M,CHUNG L L,TEONG L K,et al. Synthesis of activated carbon from lignocellulosic biomass and its applications in air pollution control:A review[J]. Journal of Environmental Chemical Engineering,2013,1(4):658-666.
[3] 罗伟,杨万泰. 可再生资源基生物质材料的研究进展[J]. 高分子通报,2013(4):36-41.
[4] 张伟,储富祥,王春鹏. 生物质基泡沫材料的最新研究进展[C]//2009年中国绝热节能材料协会年会论文集. 北京:中国绝热节能材料协会,2009:64-70.
[5] KRISTOF R,LOGAR J K. Direct LSC method for measurements of biofuels in fuel[J]. Talanta,2013,111:183-188.
[6] American Society for Testing and Materials. ASTM D6866-12 Standard test methods for determining the biobased content of solid,liquid,and gaseous samples using radiocarbon analysis[S]. USA:ASTM,2012.
[7] European Committee for Standardization. CEN/TS 15440:2006 Solid recovered fuels:Method for the determination of biomass content[S]. EU:CEN,2006.
[8] SEVERIN M,VELIS C A,LONGHURST P J,et al. The biogenic content of process streams from mechanical-biological treatment plants producing solid recovered fuel. Do the manual sorting and selective dissolution determination methods correlate?[J]. Waste Management,2010,30(7):1171-1182.
[9] ARIYARATNE W K H,ASGAUTAEN Ø,MELAAEN M C,et al. Determination of fossil fraction of refuse derived fuel by the selective dissolution method in calorific value basis:Development of simplified method[J]. Fuel,2012,98:41-47.
[10] STABER W,FLAMME S,FELLNER J. Methods for determining the biomass content of waste[J]. Waste Management & Research,2008,26(1):78-87.
[11] ARIYARATNE W K H,MELAAEN M C,TOKHEIM L A. Determination of biomass fraction for partly renewable solid fuels[J]. Energy,2014,70:465-472.
[12] 陈铁梅. 液体闪烁计数法应用于¹⁴C年代测定的实验误差分析[J]. 核技术,1982(5):48-49,43.
[13] 周卫健,周明富,杨礼平. ¹⁴C测年系列方法中的小样品¹⁴C液体闪烁计数测年法[J]. 地球化学,1995,24(2):146-151.
[14] 尹金辉,郑勇刚,刘粤霞. 古地震¹⁴C年龄的日历年代校正[J]. 地震地质,2005,27(4):678-688.
[15] 卢雪峰,周卫建. 放射性碳测年国际比对活动的初步结果[J]. 地球化学,2003,32(1):43-47.
[16] MENDONCA M L T G,GODOY J M,CRUZ R P,et al. Radiocarbon dating of archaeological samples (sambaqui) using CO₂ absorption and liquid scintillation spectrometry of low background radiation[J]. Journal of Environmental Radioactivity,2006,88(3):205-214.
[17] 杨怀元. 环境¹⁴C的取样与分析方法[J]. 疆射防护通讯,1990(1):53-57.
[18] 沈承德,黄宝林. ¹⁴C年龄测定的液体闪烁计数法[J]. 地球化学,1980(3):278-281.
[19] 卞正柱,张珏,张金卫. 液体闪烁计数器进展简述[J]. 核电子学与探测技术,2006,26(4):536-538.
[20] 姜国华. 液体闪烁测量中的淬灭和淬灭校正[J]. 中国现代教育装备,2007(10):16-18.
[21] 翁云宣,刁晓倩. 液闪计数器法测定材料中生物基含量[J]. 现代化工,2013,33(6):136-141.
[22] 郭项雨,李丕,李海玉,等. 液体闪烁计数法测定生物塑料中生物基含量[J]. 分析试验室,2014,33(11):1312-1316.
[23] BRONIC' I K,HORVATINČIČ N,BAREŠIC' J,et al. Measurement of ¹⁴C activity by liquid scintillation counting[J]. Applied Radiation and Isotopes,2009,67(5):800-804.
[24] MOHN J,SZIDAT S,FELLNER J,et al. Determination of biogenic and fossil CO₂ emitted by waste incineration based on ¹⁴CO₂ and mass balances[J]. Bioresource Technology,2008,99(14):6471-6479.
[25] BRUNNERMEIER M J,SCHMIED S A K,BOGE M M,et al. Dating of ivory from 20th century by determination of ¹⁴C by the direct absorption method[J]. Applied Radiation and Isotopes,2012,70(8):1595-1602.
[26] NORTON G A,DEVLIN S L. Determining the modern carbon content of biobased products using radiocarbon analysis[J]. Bioresource Technology,2006,97(16):2084-2090.
[27] NORTON G A,CLINE A M,THOMPSON G C. Use of radiocarbon analyses for determining levels of biodiesel in fuel blends:Comparison with ASTM Method D7371 for FAME[J]. Fuel,2012,96:284-290.
[28] YUNOKI S,SAITO M. A simple method to determine bioethanol content in gasoline using two-step extraction and liquid scintillation counting[J]. Bioresource Technology,2009,100(23):6125-6128.
[29] NAGAKAWA Y,YUNOKI S,SAITO M. Liquid scintillation counting of solid-state plastic pellets to distinguish bio-based polyethylene[J]. Polymer Testing,2014,33:13-15.
[30] CULP R,CHERKINSKY A,PRASAD G V R. Comparison of radiocarbon techniques for the assessment of biobase content in fuels[J]. Applied Radiation and Isotopes,2014,93:106-109.
[31] TUDYKA K,PAWLYTA J. Biocomponent determination in vinegars with the help of ¹⁴C measured by liquid scintillation counting[J]. Food Chemistry,2014,145:614-616.
[32] 仇士华,蔡莲珍,陈铁梅,等. 碳-14测定年代用"中国糖碳标准"的建立[J]. 科学通报,1983(3):170-174.
[33] NOAKES J,NORTON G,CULP R,et al. A comparison of analytical methods for the certification of biobased products[C]//LSC 2005:Advances in Liquid Scintillation Spectrometry,2005:259-271.
[34] QUARTA G,CALCAGNILE L,GIFFONI M,et al. Determination of the biobased content in plastics by radiocarbon[J]. Radiocarbon,2013,55(2/3):1834-1844.
[35] 郑勇刚,尹金辉,刘粤霞. Quantulua-1220型低本底液闪仪的性能测定[J]. 地震地质,2005,27(4):624-632.
[36] 周卫健,卢雪峰,武振坤,等. 西安加速器质谱中心多核素分析的加速器质谱仪[J]. 核技术,2007,30(8):702-708.
[37] NORTON G A,HOOD D G,DEVLIN S L. Accuracy of radioanalytical procedures used to determination of biobased content of manufactured products[J]. Bioresource Technology,2007,98(5):1052-1056.
[38] FUNABASHI M,OHARA K,KUNIOKA M. Accuracy of biobased carbon content of determination of plastic products and related materials by accelerator mass spectrometry[J]. Polymer Degradation and Stability,2014,109:385-392.
[39] EDLER R,KAIHOLA L. Differentiation between fossil and biofuels by liquid scintillation beta spectrometry-direct method[J]. Nukleonika,2010,55(1):127-131.
[40] MUIR G K P,HAYWARD S,TRIPNEY B G,et al. Determining the biomass fraction of mixed waste fuels:A comparison of existing industry and ¹⁴C-based methodologies[J]. Waste Management,2015,35:293-300.

Research Progress of Determination Method of Bio-based Content in Bio-based Solid Material

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Xiaopeng JIAN,Wei XU,Xinglong HOU,Shicai LIU. Research Progress on Activated Carbon Modification Technology [J]. Biomass Chemical Engineering, 2020, 54(5): 66-72.
[2]	Xue LIU,Shujun LI,Shouxin LIU,Jian LI,Zhijun CHEN. Research Progress in Preparation and Functional Application of Lignin-based Nanoparticles [J]. Biomass Chemical Engineering, 2020, 54(5): 53-65.
[3]	Weixing ZENG,Xian CHENG,Zuohui ZHANG,Liangwu BI,Zhendong ZHAO. Application Research Progress of Biological Pretreatment Technology in Extraction of Natural Products [J]. Biomass Chemical Engineering, 2020, 54(5): 45-52.
[4]	Xiaomeng QU,Ge YANG,Zehao ZHANG,Lan ZHANG. Preparation of High Purity Yacon Fructo-oligosaccharides by Nanofiltration and Its Characterization [J]. Biomass Chemical Engineering, 2020, 54(5): 37-44.
[5]	Guoqiang SONG,Huan LI,Yinmei CAO,Long TANG. Industrial Refining Process of MES Surfactant [J]. Biomass Chemical Engineering, 2020, 54(5): 33-36.
[6]	Mengmeng WANG,Lequn LIU,Zhentao LIU,Ying ZHAO. Flame Retardant Modification of Bamboo Liquefied Wall Foam Materials [J]. Biomass Chemical Engineering, 2020, 54(5): 25-32.
[7]	Peng LYU,Guanghui WANG,Bing WANG,Deyu HU. Effect of Pyrolysis Temperature and Biomass Type on Adsorption of U(Ⅵ) by Biochar [J]. Biomass Chemical Engineering, 2020, 54(5): 15-24.
[8]	Chunpo YUE,Zhiling YU,Qianhui YU,Tao WANG,Pengbo WANG,Mingwei DI. Effect of Jet Plasma Discharge in Different Atmosphere on Surface Properties of Wood-plastic Composites [J]. Biomass Chemical Engineering, 2020, 54(5): 8-14.
[9]	Zhaolan ZHAI,Pu LYU,Ping ZHAO,Zhanqian SONG,Shibin SHANG,Xiaoping RAO. Antibacterial Activity of Dehydroabietyl Nitrogen Derivatives [J]. Biomass Chemical Engineering, 2020, 54(5): 1-7.
[10]	Qiqi DAI,Xiaocui WEI,Hongbiao TANG,Jin LI,Jinjing WANG. Optimization of Microwave Assisted Pyrolysis of Coconut Clothes by Response Surface Method and Analysis of Liquid Product Composition [J]. Biomass Chemical Engineering, 2020, 54(4): 42-48.
[11]	Lin SUN,Huayu LIU,Kun LIU,Xiaoyi ZHANG,Hongxiang XIE,Rui ZHANG,Haiming LI,Chuanling SI. Research Progress in Nanocellulose Hydrophobic Modification and Applications [J]. Biomass Chemical Engineering, 2020, 54(4): 57-66.
[12]	Weijiao SHANG,Lu WANG. Status and Analysis of Nanocellulose Technology Based on Patents [J]. Biomass Chemical Engineering, 2020, 54(4): 49-56.
[13]	Ruting XU,Wei XU,Xincheng LU,Kang SUN. Novel Demineralization Technology of Phosphate-activated Carbon [J]. Biomass Chemical Engineering, 2020, 54(4): 37-41.
[14]	Yongxu LIU,Dawei ZHANG. Preparation and Properties of Bacteriostatic Chitosan/PVA/Chitosan Oligosaccharide Nanofibrous Membranes [J]. Biomass Chemical Engineering, 2020, 54(4): 30-36.
[15]	Feifei LIU,Lan WANG,Zuohu LI,Hongzhang CHEN. Dissolving Effect of Steam Exploded Corn Stalk on Phosphate Rock Powder and Influence of Its Residual on Wheat Growth [J]. Biomass Chemical Engineering, 2020, 54(4): 23-29.